Page top

Industrial Automation

Industrial Automation

EE-[]

Photomicro Sensors Accessories

EE-[]

Connectors and Connector Hold-down Clips

Product Connector
*1 *4
Connector
with Cable
*1
Connector
with Robot
Cable *1
Connector
*4
Connector
(short-
circuited
between
positive (+)
and L ter-
minals) *2 *4
Connector
with Cable
Model EE-1009 EE-1010 EE-1010-R EE-1001 EE-1001-1 EE-1006
Appearance 447_sp_1_1 447_sp_1_2 447_sp_1_3 447_sp_1_4 447_sp_1_5 447_sp_1_6
Contact resistance 20 mΩ max.
(at 20 mV max., 100 mA max.)
15 mΩ max. (at 100 VDC max.) 10 mΩ max.
(100 VDC max.)
Insertion/removal
durability *3
50 times min. ---
Insertion strength No. of poles ✕ 6 N max. 68.6 N max. 50 N max.
Surplus strength
(housing holding
strength)
No. of poles ✕ 0.4 N max. --- 20 N max.
Standard cable length --- 1 m, 2 m --- 1 m, 2 m
Lock strength *3 No. of poles ✕ 29 N min. ---
Ambient humidity - 10 to +60 °C - 10 to +75 °C - 10 to 60 °C
Material Housing Polybutylene phthalate (PBT)
Contact Phosphor bronze
Applicable
Photomicrosensors
EE-SX67[] (A, P, R) (Connector Models only), EE-SX47[], EE-SY67[], EE-SPY31[]/41[],
EE-SPX303N/403N, EE-SPW311/411

Product Connector *4 Connector
with Cable
Connector
with Cable
Connector with
Robot Cable
Connector
with Cable
Connector with
Robot Cable
Model EE-1002 EE-1003 EE-1013 EE-1016-R EE-1017 EE-1017-R
Appearance 447_sp_2_1 447_sp_2_2 447_sp_2_3 447_sp_2_4 447_sp_2_5
Contact resistance 10 mΩ max.
(at 10 mADC
and 1 ADC)
20 mΩ max. (at minute
current of 1 kHz and
500 VDC)
25 mΩ max.
(at 10 mA DC and 20 mV max.)
Insertion strength 20 N max. 23.5 N max. 40 N max. 20 N max.
Surplus strength
(housing holding
strength)
15 N max. (initial)
10 N max. (ten
times)
3.5 N max. 10 N max. 15 N min. 1.5 N min.
Cable length --- 1 m 2 m 1 m, 3 m
Ambient humidity -10 to +75°C -10 to +60°C -10 to +55°C -25 to +85°C -10 to +60°C
Material Housing Nylon
Contact Phosphor bronze (solder plating)
Applicable
Photomicrosensors
EE-SPX301/401,
EE-SPY30[]/40[],
EE-SPZ301-A/401-A
EE-SPX74[]/84[] EE-SX95[]-C1J-R EE-SX97[]C1,
EE-SX97[]P-C1

EE-[] Specifications 3

*1. The Connector has a built-in locking mechanism. To remove the Connector from the Sensor,
       grip the top and bottom of the Connector housing, as shown in the following diagram, and
       then pull out the Connector.
*2. EE-SX67[] and EE-SY67[] are the best used in the light-ON state.
*3. The insertion/removal durability and lock strength apply only to the lock mechanism.
       They do not apply to the EE-1001, EE-1001-1, and EE-1006, which do not have lock
       mechanisms.
*4. Do not store the type EE-1009, EE-1001, EE-1001-1 and EE-1002 under the following
       conditions since their terminals may discolor.
       (1) In the place exposed to the direct sunlight, the high temperature or high humidity.