CJ-series Mixed I/O Units
last update: December 19, 2022
Name | 16-point DC Input/16-point Transistor Output Unit with Fujitsu / OTAX Connectors (Sinking Outputs) | ||
---|---|---|---|
Model | CJ1W-MD231 | ||
Output section (CN1) | Input section (CN2) | ||
Rated Voltage | 12 to 24 VDC | Rated Input Voltage | 24 VDC |
Operating Load
Voltage Range |
10.2 to 26.4 VDC | Operating Input
Voltage |
20.4 to 26.4 VDC |
Maximum Load
Current |
0.5 A/point, 2.0 A/Unit | Input Impedance | 3.3 kΩ |
Maximum Inrush
Current |
4.0 A/point, 10 ms max. | Input Current | 7 mA typical (at 24 VDC) |
Leakage Current | 0.1 mA max. | ON Voltage/ON
Current |
14.4 VDC min./3 mA min. |
Residual Voltage | 1.5 V max. | OFF Voltage/OFF
Current |
5 VDC max./1 mA max. |
ON Response
Time |
0.1 ms max. | ON Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) * |
OFF Response
Time |
0.8 ms max. | ||
No. of Circuits | 16 (16 points/common, 1 circuit) | OFF Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) * |
Fuse | None | ||
External Power
Supply |
10.2 to 26.4 VDC, 20 mA min. | No. of Circuits | 16 (16 points/common,
1 circuit) |
Number of
Simultaneously ON Points |
75% (at 24 VDC) | ||
Insulation
Resistance |
20 MΩ min. between the external terminals and the GR terminal (at 100 VDC) | ||
Dielectric
Strength |
1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of
10 mA max. |
||
Internal Current
Consumption |
5 VDC 130 mA max. | ||
Weight | 90 g max. | ||
Accessories | None | ||
Circuit
Configuration |
CN1 (OUT) | CN2 (IN) | |
![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() ![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
||
External
connection and terminal-device variable diagram |
CN1 (OUT) | CN2 (IN) | |
![]() of the external power supply. The load may operate incorrectly if polarity is reversed. Be sure to wire both pins A9 and B9 (COM0 (0 V)) of CN1. Be sure to wire both pins A10 and B10 (+V) of CN1. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() CN2, and set the same polarity for both pins. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
Name | 16-point DC Input/16-point Transistor Output Unit with MIL Connectors (Sinking Outputs) | ||
---|---|---|---|
Model | CJ1W-MD233 | ||
Output section (CN1) | Input section (CN2) | ||
Rated Voltage | 12 to 24 VDC | Rated Input Voltage | 24 VDC |
Operating Load
Voltage Range |
10.2 to 26.4 VDC | Operating Input
Voltage |
20.4 to 26.4 VDC |
Maximum Load
Current |
0.5 A/point, 2.0 A/Unit | Input Impedance | 3.3 kΩ |
Maximum Inrush
Current |
4.0 A/point, 10 ms max. | Input Current | 7 mA typical (at 24 VDC) |
Leakage Current | 0.1 mA max. | ON Voltage/ON
Current |
14.4 VDC min./3 mA min. |
Residual Voltage | 1.5 V max. | OFF Voltage/OFF
Current |
5 VDC max./1 mA max. |
ON Response
Time |
0.1 ms max. | ON Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) * |
OFF Response
Time |
0.8 ms max. | ||
No. of Circuits | 16 (16 points/common, 1 circuit) | OFF Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) * |
Fuse | None | ||
External Power
Supply |
10.2 to 26.4 VDC, 20 mA min. | No. of Circuits | 16 (16 points/common,
1 circuit) |
Number of
Simultaneously ON Points |
75% (at 24 VDC) | ||
Insulation
Resistance |
20 MΩ min. between the external terminals and the GR terminal (at 100 VDC) | ||
Dielectric
Strength |
1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of
10 mA max. |
||
Internal Current
Consumption |
5 VDC 130 mA max. | ||
Weight | 90 g max. | ||
Accessories | None | ||
Circuit
Configuration |
CN1 (OUT) | CN2 (IN) | |
![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() ![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
||
External
connection and terminal-device variable diagram |
CN1 (OUT) | CN2 (IN) | |
![]() of the external power supply. The load may operate incorrectly if polarity is reversed. Be sure to wire both terminals 3 and 4 (COM0 (0 V)) of CN1. Be sure to wire both terminals 1 and 2 (+V) of CN1. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() CN2, and set the same polarity for both pins. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
Name | 32-point DC Input/32-point Transistor Output Unit with Fujitsu / OTAX Connectors (Sinking Outputs) | ||
---|---|---|---|
Model | CJ1W-MD261 | ||
Output section (CN1) | Input section (CN2) | ||
Rated Voltage | 12 to 24 VDC | Rated Input Voltage | 24 VDC |
Operating Load
Voltage Range |
10.2 to 26.4 VDC | Operating Input
Voltage |
20.4 to 26.4 VDC |
Maximum Load
Current |
0.3 A/point, 1.6 A/common, 3.2 A/Unit | Input Impedance | 5.6 kΩ |
Maximum Inrush
Current |
3.0 A/point, 10 ms max. | Input Current | 4.1 mA typical (at 24
VDC) |
Leakage Current | 0.1 mA max. | ON Voltage/ON
Current |
19.0 VDC min./3 mA
min. *2 |
Residual Voltage | 1.5 V max. | OFF Voltage/OFF
Current |
5 VDC max./1 mA max. |
ON Response
Time |
0.5 ms max. | ON Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) *1 |
OFF Response
Time |
1.0 ms max. | ||
No. of Circuits | 32 (16 points/common, 2 circuits) | OFF Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) *1 |
Fuse | None | ||
External Power
Supply |
10.2 to 26.4 VDC, 30 mA min. | No. of Circuits | 32 (16 points/common,
2 circuits) |
Number of
Simultaneously ON Points |
75% (24 points) (at 24
VDC) |
||
Insulation
Resistance |
20 MΩ min. between the external terminals and the GR terminal (at 100 VDC) | ||
Dielectric
Strength |
1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current
of 10 mA max. |
||
Internal Current
Consumption |
5 VDC 140 mA max. | ||
Weight | 110 g max. | ||
Accessories | None | ||
Circuit
Configuration |
CN1 (OUT) | CN2 (IN) | |
![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
||
![]() |
|||
External
connection and terminal-device variable diagram |
CN1 (OUT) | CN2 (IN) | |
![]() (COM0 (0 V)) of CN1. Be sure to wire both terminals B19 and B9 (COM1 (0 V)) of CN1. Be sure to wire both terminals A20 and A10 (+V) of CN1. Be sure to wire both terminals B20 and B10 (+V) of CN1. When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if polarity is reversed. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() CN2, and set the same polarity for both pins. Be sure to wire both pins B9 and B18 (COM3) of CN2, and set the same polarity for both pins. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
Name | 32-point DC Input/32-point Transistor Output Unit with MIL Connectors (Sinking Outputs) | ||
---|---|---|---|
Model | CJ1W-MD263 | ||
Output section (CN1) | Input section (CN2) | ||
Rated Voltage | 12 to 24 VDC | Rated Input Voltage | 24 VDC |
Operating Load
Voltage Range |
10.2 to 26.4 VDC | Operating Input
Voltage |
20.4 to 26.4 VDC |
Maximum Load
Current |
0.3 A/point, 1.6 A/common, 3.2 A/Unit | Input Impedance | 5.6 kΩ |
Maximum Inrush
Current |
3.0 A/point, 10 ms max. | Input Current | 4.1 mA typical (at 24
VDC) |
Leakage Current | 0.1 mA max. | ON Voltage/ON
Current |
19.0 VDC min./3 mA
min. *2 |
Residual Voltage | 1.5 V max. | OFF Voltage/OFF
Current |
5 VDC max./1 mA max. |
ON Response
Time |
0.5 ms max. | ON Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) *1 |
OFF Response
Time |
1.0 ms max. | ||
No. of Circuits | 32 (16 points/common, 2 circuits) | OFF Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) *1 |
Fuse | None | ||
External Power
Supply |
10.2 to 26.4 VDC, 30 mA min. | No. of Circuits | 32 (16 points/common,
2 circuits) |
Number of
Simultaneously ON Points |
75% (24 points) (at 24
VDC) |
||
Insulation
Resistance |
20 MΩ min. between the external terminals and the GR terminal (at 100 VDC) | ||
Dielectric
Strength |
1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of
10 mA max. |
||
Internal Current
Consumption |
5 VDC 140 mA max. | ||
Weight | 110 g max. | ||
Accessories | None | ||
Circuit
Configuration |
CN1 (OUT) | CN2 (IN) | |
![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
||
![]() |
|||
External
connection and terminal-device variable diagram |
CN1 (OUT) | CN2 (IN) | |
![]() (COM0) of CN1. Be sure to wire both terminals 3 and 4 (COM1) of CN1. Be sure to wire both terminals 21 and 22 (+V) of CN1. Be sure to wire both terminals 1 and 2 (+V) of CN1. When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if polarity is reversed. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() CN2, and set the same polarity for both pins. Be sure to wire both pins 3 and 4 (COM3) of CN2, and set the same polarity for both pins. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
Name | 16-point DC Input/16-point Transistor Output Unit with MIL Connectors (Sourcing Outputs) | ||
---|---|---|---|
Model | CJ1W-MD232 | ||
Output section (CN1) | Input section (CN2) | ||
Rated Voltage | 24 VDC | Rated Input Voltage | 24 VDC |
Operating Load
Voltage Range |
20.4 to 26.4 VDC | Operating Input
Voltage |
20.4 to 26.4 VDC |
Maximum Load
Current |
0.5 A/point, 2.0 A/Unit | Input Impedance | 3.3 kΩ |
Leakage Current | 0.1 mA max. | Input Current | 7 mA typical (at 24 VDC) |
Residual Voltage | 1.5 V max. | ON Voltage/ON
Current |
14.4 VDC min./3 mA min. |
ON Response
Time |
0.5 ms max. | OFF Voltage/OFF
Current |
5 VDC max./1 mA max. |
OFF Response
Time |
1.0 ms max. | ON Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) * |
Load Short-
circuit Protection |
Detection current: 0.7 to 2.5 A min.
Automatic restart after error clearance. |
OFF Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) * |
No. of Circuits | 16 (16 points/common, 1 circuit) | No. of Circuits | 16 (16 points/common,
1 circuit) |
External Power
Supply |
20.4 to 26.4 VDC, 40 mA min. | Number of
Simultaneously ON Points |
75% (at 24 VDC) |
Insulation
Resistance |
20 MΩ min. between the external terminals and the GR terminal (at 100 VDC) | ||
Dielectric
Strength |
1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of
10 mA max. |
||
Internal Current
Consumption |
5 VDC 130 mA max. | ||
Weight | 100 g max. | ||
Accessories | None | ||
Circuit
Configuration |
CN1 (OUT) | CN2 (IN) | |
![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
||
![]() |
|||
External
connection and terminal-device variable diagram |
CN1 (OUT) | CN2 (IN) | |
![]() of the external power supply. The load may operate incorrectly if polarity is reversed. Be sure to wire both terminals 3 and 4 (COM0 (+V)) of CN1. Be sure to wire both terminals 1 and 2 (0 V) of CN1. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() CN2, and set the same polarity for both pins. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
Name | 32-point Input /32-point Output TTL I/O Unit with MIL Connectors | ||
---|---|---|---|
Model | CJ1W-MD563 | ||
Output section (CN1) | Input section (CN2) | ||
Rated Voltage | 5 VDC±10% | Rated Input Voltage | 5 VDC±10% |
Operating Load
Voltage Range |
4.5 to 5.5 VDC | Input Impedance | 1.1 kΩ |
Maximum Load
Current |
35 mA/point, 560 mA/common, 1.12 A/Unit | Input Current | Approx. 3.5 mA (at 5
VDC) |
Leakage Current | 0.1 mA max. | ON Voltage | 3.0 VDC min. |
Residual Voltage | 0.4 V max. | OFF Voltage | 1.0 VDC max. |
ON Response
Time |
0.2 ms max. | ON Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) * |
OFF Response
Time |
0.3 ms max. | OFF Response Time | 8.0 ms max. (Can be set
to between 0 and 32 in the Setup.) * |
No. of Circuits | 32 points (16 points/common, 2 circuits) | ||
Fuse | None | No. of Circuits | 32 points (16 points/
common, 2 circuits) |
External Power
Supply |
5 VDC ± 10%, 40 mA min.
(1.2 mA × No. of ON points) |
Number of
Simultaneously ON Points |
100% (16 points/
common) |
Insulation
Resistance |
20 MΩ min. between the external terminals and the GR terminal (at 100 VDC) | ||
Dielectric
Strength |
1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of
10 mA max. |
||
Internal Current
Consumption |
5 VDC 190 mA max. | ||
Weight | 110 g max. | ||
Accessories | None | ||
Circuit
Configuration |
CN1 (OUT) | CN2 (IN) | |
![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() device variable names. The device variable names are the names that use "Jxx" as the device name. |
||
External
connection and terminal-device variable diagram |
CN1 (OUT) | CN2 (IN) | |
![]() of the external power supply. The load may operate incorrectly if the polarity is reversed. Be sure to wire both terminals 23 and 24 (COM0) of CN1. Be sure to wire both terminals 3 and 4 (COM1) of CN1. Be sure to wire both terminals 21 and 22 (+V) of CN1. Be sure to wire both terminals 1 and 2 (+V) of CN1. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
![]() CN2, and set the same polarity for both pins. Be sure to wire both pins 3 and 4 (COM3) of CN2, and set the same polarity for both pins. The signal names of the terminals are the device variable names. The device variable names are the names that use "Jxx" as the device name. |
Allocated CIO word | Signal name ( |
|
CIO | Bit | |
Wd m
( |
00 | OUT0/ |
01 | OUT1/ |
|
: |
: |
|
14 | OUT14/ |
|
15 | OUT15/ |
|
Wd m+ ( |
00 | IN0/ |
01 | IN1/ |
|
: |
: |
|
14 | IN14/ |
|
15 | IN15/ |
Allocated CIO word | Signal name ( |
|
CIO | Bit | |
Wd m
( |
00 | OUT0/ |
01 | OUT1/ |
|
: |
: |
|
14 | OUT14/ |
|
15 | OUT15/ |
|
Wd m+ ( |
00 | OUT0/ |
01 | OUT1/ |
|
: |
: |
|
14 | OUT14/ |
|
15 | OUT15/ |
|
Wd m+ ( |
00 | IN0/ |
01 | IN1/ |
|
: |
: |
|
14 | IN14/ |
|
15 | IN15/ |
|
Wd m+ ( |
00 | IN0/ |
01 | IN1/ |
|
: |
: |
|
14 | IN14/ |
|
15 | IN15/ |
last update: December 19, 2022